汉译英在线翻译句子

1. Power Switch
Function is on / off controller working power source.
2. Amplitude modulator
Is used to control the waveform duty cycle to regulate its function is within a certain range to change the vibration amplitude plating on the plating speed from micro-adjustment feature.
3. Velocity regulator
Waveform is used to control the frequency of adjustment, the main function is to adjust speed plating.
4. Insurance Block
10A - Output DC insurance seat, when the overcurrent protection for the components used.
5. 6 terminals
Input for the power supply, while the output control signals to the vibration plate machine.
6. Wiring diagram of the external terminals 6 Figure (D).

五. Instructions
1. Ensure that the vibration plate machine power input line is correct, the normal power supply, reliable, vibration plate fixed to the scaffold;
2. For the first time use, should be amplitude and velocity regulator scale are transferred 0.
3. POWER pull the power switch to the ON state.
4. With adjustable speed and amplitude adjustment potentiometer, so that plating velocity in the setting / best condition for continuous vibration plate.
Note: in the regulation of speed and amplitude adjustment potentiometer, the first edge of the potentiometer a small black body, (called "lock potentiometer settings" button), counter-clockwise to set the drawing state, before they can be carried out on the potentiometer setting and regulation. Adjust to normal, we should "lock potentiometer settings" button in a clockwise direction pulling the lock to ensure that it does not out technical errors, otherwise set the parameters of the drift due to the quality of products would be adversely influence, and in severe damage to the machine so that vibration plate.
5. Shutdown / or stop the vibration plate when the POWER dial directly to the power switch to the OFF position, cut off the power supply controller can be.

六. Fault Detection
1. No vibration, and the power switch POWER indicator light does not shine.
Approach: Are there any power supply; DC fuse is blown.
2. No vibration, but the power switch POWER indicator light.
3. Approach: 1) Check the scale of the amplitude modulator is greater than 4.
2) Check the e-board, components, and whether there is loose wiring, broken.
3) Check the output control signal cable is open circuit.
Other matters: Please refer to the narrative part of mechanical vibration plate machine

7. Notes
1. The controller is strictly prohibited without customs of electricity allocated among the various contact socket;
2. Potentiometer is prohibited under the late unlocking adjustment potentiometer;
3. Abnormal failure can not be excluded, it shall promptly notify the professional staff carry out maintenance operations.

Figure D 6 terminal wiring diagram
五. Instructions
1. Ensure that the vibration plate machine power input line is correct, the normal power supply, reliable, vibration plate fixed to the scaffold;
2. For the first time use, should be amplitude and velocity regulator scale are transferred 0.
3. POWER pull the power switch to the ON state.
4. With adjustable speed and amplitude adjustment potentiometer, so that plating velocity in the setting / best condition for continuous vibration plate.
Note: in the regulation of speed and amplitude adjustment potentiometer, the first edge of the potentiometer a small black body, (called "lock potentiometer settings" button), counter-clockwise to set the drawing state, before they can be carried out on the potentiometer setting and regulation. Adjust to normal, we should "lock potentiometer settings" button in a clockwise direction pulling the lock to ensure that it does not out technical errors, otherwise set the parameters of the drift due to the quality of products would be adversely influence, and in severe damage to the machine so that vibration plate.
5. Shutdown / or stop the vibration plate when the POWER dial directly to the power switch to the OFF position, cut off the power supply controller can be.

六. Fault Detection
1. No vibration, and the power switch POWER indicator light does not shine.
Approach: Are there any power supply; DC fuse is blown.
2. No vibration, but the power switch POWER indicator light.
3. Approach: 1) Check the scale of the amplitude modulator is greater than 4.
2) Check the e-board, components, and whether there is loose wiring, broken.
3) Check the output control signal cable is open circuit.
Other matters: Please refer to the narrative part of mechanical vibration plate machine

7. Notes
1. The controller is strictly prohibited without customs of electricity allocated among the various contact socket;
2. Potentiometer is prohibited under the late unlocking adjustment potentiometer;
3. Abnormal failure can not be excluded, it shall promptly notify the professional staff carry out maintenance operations.

Abstract:
With
today's
scientific
and
technological
development,
new
technology
and
modern
educational
methods
widely
used
in
the
continuous
updates,
multimedia
technology
began
to
allow
the
entry
of
Track
and
Field
classrooms.
Multimedia
technology
into
the
teaching
track
and
field
class,
has
many
advantages:
to
improve
the
traditional
education
model;
give
full
play
to
the
teaching
open;
students
motivation
to
learn;
stimulate
student
interest
in
learning.
Dan
in
the
actual
operation
of
them,
that
we
should
pay
attention
to,
not,
for
the
multimedia
and
application
of
multimedia,
multimedia
application
to
Wei
quality
education
services;
to
autonomy
of
students,
creative
learning
services;
to
the
opening
teaching
service.
自己在检查下！

i’mgoingoutshopping,andwon’tbebackuntilabout5:00pm.ihavetakenwithmethetwobooksyouaskedmetoreturntothecitylibrary.atabout1o’clockthisafternoon,tracycalled,sayingthatshecouldn’tmeetyouatboltoncoffeetomorrowmorningasshehassomethingimportanttoattendto.shefeltverysorryaboutthat,butsaidthatyoucouldsetsomeothertimeforthemeeting.shewantedyoutocallherbackassoonasyouarehome.shehasalreadytoldsusanaboutthischange.

Each
year,
all
live
without
valentine
on
the
Valentine's
Day!

Every
year,
is
not
the
lover's
valentine's
day!